the grammar being wrong also bothers me

    • dual_sport_dork 🐧🗡️@lemmy.worldM
      link
      fedilink
      arrow-up
      6
      arrow-down
      2
      ·
      edit-2
      19 hours ago

      What this commenter wrote almost makes sense if this camera were an oldschool analog device, think the era of tape camcorders and VCRs and so forth. And tube televisions and even the retro game consoles connected to them, for that matter. These machines were all heavily tied to the frequency and timings of their native video signal format, either NTSC or PAL (or even SECAM, if you want to get really obscure).

      This is absolutely not the case with a modern flagship mirrorless camera like the Sony ɑ7RII in OP’s picture. It is obviously not only eminently capable of altering its shutter rate, sensor refresh speed, and video recording frame rate to any arbitrary value but is purpose built to be able to do so. The only part of its componentry at all that is operating at NTSC/PAL frequencies at any point is whatever tiny amount of DAC hardware it’s using to output that low-def TV signal (probably composite video) out the little barrel jack on the side, and even then only when you’ve got it plugged into an analog TV.

      Analog NTSC and PAL are very different from each other. Digital “NTSC” and “PAL” (in reality there’s really no such thing) are not. The block of NTSC countries have TV’s that expect a 60hz frame rate and those in traditionally PAL countries expect a 50hz frame rate. That’s literally it.

      The following claims are bogus:

      You can fake the video with just the framerate

      No, that’s literally what digital HD video does nowadays, like the type you’d transmit over an HDMI cable.

      implies the entire electric circuit ran at a specific frequency

      This was true for analog devices and those whose timings had to be tied to the output frequency, but is not the case for a digital device that handles all of its signal processing internally.

      Which is easier to do if everything inside the camera, shutter, pixel refresh, encoding, etc. runs on the same frequency.

      This is not even remotely what a high end modern camera does. Sony is obviously mum about the exact specifications of the “Bionz X” main image processor in the ɑ7RII, but it is obviously a modern highly specialized chip most likely running at many hundreds of megahertz, completely independent of the camera’s external video output.

      If the camera can be fed with direct power it will also condition the internal components frequency.

      I think this grammatically malformed statement is trying to imply that the camera must run in lockstep with its input power frequency. If so, this could only be true if the camera were an analog device running directly off of mains current from a wall outlet. This is not so for any digital camera; they’re DC devices primarily fed from their battery which obviously has no electricity frequency and secondarily if they’re externally powered this is also through DC from an AC to DC step down converter. No part of the mains voltage frequency should be making it to the camera. If it did, this would be very bad. Smoke would certainly be involved.

      Furthermore, the mains voltage frequency is not nearly accurate or consistent enough to tie the operating frequency of any electronic device to it. You can easily observe this with oldschool analog clocks which derive their drive speed directly from the 50 or 60hz frequency of their mains power supply; they don’t keep very good time. So electronic devices even if they ostensibly “run at” their countries’ analog TV frequency at 60 or 59.94 or 50hz or whatever still use their own internal crystal oscillators to create that frequency accurately rather than blithely relying on the mains frequency.

      If it is for sync when recording screens or using old lights, the entire camera must run on the same frequency, or the skip when faking framerates is actually still noticeable.

      Once again it is trivially verifiable that this is not so; I have point and shoot cameras from the early 2000s which can change both their flash sync and screen sync settings on the fly with no ill effect, no reboot or reformat required, and the results are clearly visible. Anybody with a camera in their hands could verify this in about four seconds without having to resort to spouting any bullshit.

      All this would require restarting the electronics to run on the correct frequency.

      No, it just requires setting the recording framerate to the correct value and optionally tuning to start the frame exposure at the correct time. Which again, any competent digital camera can already do.

      The old encodes go beyond just containers, they do bitwise manipulation as well. Electrical system agnosticism is a modern result of newer container formats.

      This is either willfully or ignorantly conflating the way that analog and digital video encoding work, with a sprinkling of buzzwords thrown in for good measure.

      (Edits: I fixed a spelling error and removed a duplicated couple of clauses.)