Reddit refuge, escentric engineer and serial hobbyist.
So you have photoprism pointed to a folder but you push photos into the folder witb syncthing. How do you trigger the re-index or its somehow automatic? I run my photoprism in docker and I always had to manually trigger the index after changes to the folder.
As someone who has and still used photoprism for over two years and donated heavily…steer clear. Their update cycle is slow and the things they keep adding don’t seem helpful. Still no multi-user support. If you don’t upload new photos via photoprism using WebDAV you have to make your own scripts to watch for changes and refresh which took a lot of time for me to setup.
I’m just going to start using Nextcloud and Memories app going forward.
Most folks ignore laptops, but if you’re OK with USB storage or getting the special caddy to install the internal 2.5" drive you can get great deals on laptops. This one idles around 4W with the screen off.
Install Enocean wireless, battery free switches. I’ve used them for many years, they work awsome. The switches can go anywhere you want (double side tape on any surface) or screw in as normal light switches. The act of pushing the button generates enough energy to send the RF signal to a receiver you install with the light and its powered from AC mains.
Been using it for over a year on two 8tb SSDs in strip and 14tb as mirror. This is on Debian and its flawless and wonderful. I run btrkbk hourly for snapshots, backups to remote locations and house keeping with 6 months of hourly snaps. Life is great.
I have the micro form factor I assume the same as you. Basically just a laptop in a small desktop case. I never installed tlp I’ll have to give that a shot but I’m pretty sure it’s optimized. I have two as servers and one as a router and I’d love to get it down to 12w total! I monitor the whole server rack with an iotawatt and all my servers and networking gear hovers around 75w idle.
I’d question that. I have three 3080 and they’re consistently about 8W each with one ssd and onboard graphics. I even went so far to splice three barrel jacks to a single 60w power supply that powers all three to avoid the losses of an additional 2 power supplies and this gets me the 8w idle power with Debian and throttling.
At the risk of sounding like an oaf I just use an excel document, and these days I just keep it in nextcloud and edit it via a browser while in the driveway. Each car gets a sheet. Keeping it simple.
Ditto, though I’m getting more and more resentful by the day at the lack of multi user support. I’m not going to donate to them again.
I hear ya but my instance is old (before i knew docker) and just works on the rails. I also tweak the heck out of it for performance so I deal with the annoyance once every two years. If it completely blows up I might roll it on docker.
I understand that everyone doesn’t always have a perfect experience but I’ve been using the same instance of nextcloud for over 8 years I just keep upgrading and migrating. It just works. Only issues I’ve had is when Debian withholds updating php for too long or when they finally do all the config files for php get fucked and I have to redo them all.
Here is the list!
1 x Samsung SSD 980 1TB
1 x Adata XPG SX8200 Pro 2TB
2 x Samsung SSD 870 QVO 8TB
1 x Western digital engineering sample. Cannot comment. 4TB
1 x Seagate Exos X16 14tb
My server is a ryzen 5600g based and has; 2 x m.2 SSDs, 3xSATA SSDs (20TB) and one spun down mechanical disk (14TB) and my total idle power is around 27W. The mechanical disk is the only notable load, unplugging it can save me 5W idle and when it spins up its about 15W total. I can give you specific model numbers if you like.
I’m sorry but wireguard is not easy for beginners and the quick QR code generator in the command line was fantastic and light years ahead of fumbling around with getting config files securely to a mobile device.
Been using afraid.org for well over 10 years and use dynamic dns to have various subdomains pointing to different IP addresses/hosts I have in physically different places. It just works and I login maybe once every 3-4 years.
Listen to this guy! Spot on. When I built my server I spent more time researching and paying for the PSU more than any other single part. Ended up with a Seasonic PRIME FANLESS PX-450. Server idles around 25W with a ryzen 5600g and 40TB of storage.
Every link should open a separate pop up window. Add an under construction gif of a dude digging.
I’m going to have to give this a shot tonight, need to make a pfsense rule to allow the server to get out and then change its DNS. Regarding php, my current config is the following because I have over 64gigs of ram and went through great length to get Nextcloud to cache MORE into ram:
pm.max_requests = 50000 #set higher, the process is recyled after 50k calls to prevent memory leaks
pm.max_children = 1000
pm.start_servers = 60
pm.min_spare_servers = 30
pm.max_spare_servers = 120
So on your Nextcloud server you use an external DNS and it greatly sped up you nextcloud? Because I noticed a few years back mine got slow and I cannot figure out why. It was about the time I enforced pihole dns with pfsense. I might need to try this.
I bought all the gear to do 10gbe but ultimately went back to 1gig simply because the power consumption. The switch alone used 20w at idle and each NIC burned 8w and I couldn’t justify it.